Ah, my personal favorite on the job site (and at home). This way I don't get stuck with a Phillips when I need a slotted and visa-versa. These well-made screwdrivers come with interchangeable Phillips head tips (large & small) and slotted tips (large & small) stored in the metal shaft in the red handle. Overall length: 5-1/4"

You'll need this screwdriver handle and your choice of driver bits to fasten and unfasten our security head screws. The driver handle comes "empty",  without a driver bit so be sure to also order whichever bit matches your screws.

The No. 6 Spanner Bit is for No. 6 wood screws and No. 6-32 machine screws.

The No. 8 Spanner Bit for No. 8 wood screws.

The Pin-head Phillips Bit fits all the pin-head Phillips screws.

These knives combine stiffness and sharpness, making them particularly useful for cutting shapes in Ethafoam. The square point knives are good for straight lines, while the pottery knife lends itself to making curved shapes. The sharpness of the blades on these knives permits you to cut fine, detailed shavings from Ethafoam blocks.

For best results, sharpen frequently during use - we recommend either our handy Knife Sharpener or Diamond Hone, below.

An essential companion to the foam knives or any knife!  Keeps them sharp.  Use it dry, without oil.  It sharpens very fast.  Made of industrial diamonds set into a plastic matrix, it comes with a protective leather sheath.

We use these gauges to size the brass stem of the mount before we drill into the case for installation. For a tight fit, choose a drill bit one size smaller than the stem diameter; for an easy fit, choose the same size.

A hard, fine point for scribing and marking out lines on brass, stainless steel, plexiglas, etc. Comes with four spare points stored under the cap.

Indispensable when you need to know the size of the brass you're working with. The sliding action, since brass is a "self-lubricating" metal, just gets better with time.  
Divided into 16ths and mm, opens to 3.149"/ 80mm . 
Made in Germany.

We're no longer able to carry this item but we kept it here to remind you of its use, to hope you have one or can get one and because we love the drawing!

To clean burrs from the edges of holes drilled in brass, or to remove flash from the inside of sawn tubing. Also a must for making a hole just a wee bit bigger. Tapered for holes from 1/8" to 1/2" diameter.

For delicate placements, getting threads out of the way, pulling splinters, etc. Stainless steel with a fine serrated point and serrated finger grip area. 4-1/2" long, opens wide to 5/8".

We've had made what we consider to be the easiest to use and most versatile of pinning pliers, a copy of the customized ones that we've used for over 30 years. These pliers have a groove across one jaw for a firm grip on pins and a curved nose to provide a fulcrum for leverage. Made for us in Germany.

Of polished steel with box joint construction and PVC-coated handles, 5-1/8" long.

The chain nose plier has short round jaws which are good for making a range of angled bends. They are made of polished steel with box joint construction and PVC-coated handles. 5-1/8" long.

We're very happy to announce that the forming pliers are back! Here's our old favorite back, fresh off the boat from Germany, with jaws shaped to our specifications. One jaw is flat, one is round. We use them all the time to make either sharply angled or curved bends, as needed. Made of polished steel with box joint construction and PVC-coated handles. 5-1/8" long.

Measurement underlies all installation and mountmaking work.  This rugged Stanley retractable rule has a broad, yellow ruler surface, graduated in feet and inches on one edge and in centimeters on the other.  You'll need them both.  Overall length is 10'/3m.