PHOTOS

T mount - brass rod stem for wall or deck mounting with a lighter weight cross-bar. Rod and cross-bar can be formed to support various kinds of objects, padded with heat-shrinkable tubing or sprayed with Krylon and painted-out to blend in with objects or background. 

Sold 6 per package.

PHOTOS

"Spider" mounts because of all the legs... We didn't go for eight, but the three cross-bar arms give support to a spider's nest of objects with complex shapes. Also known as "Y mounts"!

Sold 6 per package.

PHOTOS

This mount hangs a plate on the wall. Two bottom tabs get shaped to your plate's profile and hold the weight. The top tab also gets shaped to your plate's profile and then slides into a tube to lock the plate in place. Drill an undersized hole in the backboard when you install the stem. 

 Sold individually.

PHOTOS

For the deck mount, the two tabs get shaped to your plate's profile and hold the weight. Bend the stem so that the plate leans back into the mount. Drill an undersized hole into the deck when you install the stem.

Sold individually.

The U-Clip Kit is a simple plexiglas & brass mounting device that allows for easy installation of single documents, photographs, thin closed volumes or magazines. In this kit, the plexiglas U-Clip is glued to a single plexiglas plate with lip. Your choice of three different size plates: Mini (4" x 6"), Standard (4-1/2" x 8"), Intermediate (7" x 11").  The brass stem gets bent to your desired angle for wall or deck installation. Your artifact gets strapped to the plexiglas plate using our Poly Strap and that entire  assembly then easily slips onto the installed brass stem. 

Watch our U-Clip & Brass Stem Demonstration on our Youtube channel. 

For those that would like to use our U-Clip and brass stem, but have their own plex plate and the ability to glue the U-Clip on to that plate, here are the independent parts! Glue the U-Clip to a single plexiglas plate with lip. Bend the brass stem to your desired angle for wall or deck installation. Install the stem into the case. Strap your artifact to the plexiglas plate using our Poly Strap. Slip the entire assembly onto the installed brass stem. 

U-Clips and brass stems are sold in sets of four.

For assembly, you’ll need plexiglas solvent-weld glue (available at amazon.com and elsewhere).

4" long rod stems with a 3" lengths of strap soldered to one end.  We provide them straight and annealed: you bend them to fit your objects. 
       
Sold 6 per package.

PHOTOS

A 1/4" diameter, 18" long brass stem with a pointed top end, fitted with a 2" x 3" brass plate. Carve the 4" x 8" x 8" Ethafoam block to fit inside your hat, stick it on the pointy end of the brass stem. (To finish off, we cover the top part of the Ethafoam with stockinette and cut a sheet of dark felt to cover the bottom of the Ethafoam, including the brass plate. The stockinette is kind to the object and the dark felt helps the mount "disappear".) Then bend the stem to the shape you need. Install in deck or wall.

Sold individually.

PHOTOS

Used to securely cradle round bottomed bowls, etc.  Three fully annealed arms get shaped to fit the bottom of your bowl. Pad them, paint them, fix mount to the deck with a standard drywall screw. For top-heavy items, place one of our weight bags inside to help stabilize.

Sold individually.

PHOTOS

Used to support objects with cylindrical or oval-section shafts angled out or up from the wall or deck. We solder two straps one above the other on the opposite sides of a sturdy rod.  The opposing straps provide leverage to support the object, the lower one wrapping up and over the shaft and the upper one wrapping down and under.

Sold Individually.

When you need to steady an artifact up against the wall (either on a shelf or with its own bottom clips), these little gems save more time and make an installation easier than you can imagine. Make a "drop-clip" with our 1/8"th. x 1/2"w. brass strap (as seen by the dotted clip in our drawing). Fit it to the shape of your object. Be sure to allow for padding as required. Screw the drop-clip channel into the wall behind the object. Put the art in place and slide the shaped "drop clip" into this channel. It secures the art gently but firmly in place.  

Our Brass Strap 22-127 can be used to make the clips that fit each piece's 1/2" wide channel - click here to add to your cart.

Fabricated here in Rosemont, N.J.
Sold 6 per package.